ASTM A36 A36M-14 Standard Specification for Carbon Structural Steel

文档天下 国外标准评论6阅读模式

1 Scope*

1.1 This specification
2 covers carbon steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes.

1.2 Supplementary requirements are provided for use where additional testing or additional restrictions are required by the purchaser. Such requirements apply only when specified in the purchase order.

1.3 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.

1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.

1.5 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

1.6 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of A6/A6M apply.

2 Referenced Documents

2.1 ASTM Standards:
3

A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

A27/A27M Specification for Steel Castings, Carbon, for General Application

A307 Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength

A325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

A325M Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric)

A500 Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes

A501 Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing

A502 Specification for Rivets, Steel, Structural

A563 Specification for Carbon and Alloy Steel Nuts

A563M Specification for Carbon and Alloy Steel Nuts (Metric)

A668/A668M Specification for Steel Forgings, Carbon and Alloy, for General Industrial Use

A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

A1018/A1018M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

F568M Specification for Carbon and Alloy Steel Externally

1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.02 on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.

Current edition approved Dec. 1, 2014. Published December 2014. Originally approved in 1960. Last previous edition approved in 2012 as A36/A36M – 12. DOI: 10.1520/A0036_A0036M-14.

2 For ASME Boiler and Pressure Vessel Code Applications, see related Specifications SA-36 in Section II of that Code.

3 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards volume information, refer to the standard’s Document Summary page on the ASTM website.

TABLE 1 Appurtenant Material Specifications

NOTE 1—The specifier should be satisfied of the suitability of these materials for the intended application. Chemical composition or mechanical properties, or both, may be different than specified in A36/A36M.
Material ASTM Designation
Steel rivets A502, Grade 1
Bolts A307, Grade A or F568M, Class 4.6
High-strength bolts A325 or A325M
Steel nuts A563 or A563M
Cast steel A27/A27M, Grade 65-35 [450-240]
Forgings (carbon steel) A668/A668M, Class D
Hot-rolled sheets and strip A1011/A1011M, SS Grade 36 [250] Type 1 or Type 2 or A1018/A1018M, SS Grade36 [250]
Cold-formed tubing A500, Grade B
Hot-formed tubing A501
Anchor bolts F1554, Grade 36

Threaded Metric Fasteners (Metric) (Withdrawn 2012) F1554 Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength

3 Appurtenant Materials

3.1 When components of a steel structure are identified with this ASTM designation but the product form is not listed in the scope of this specification, the material shall conform to one of the standards listed in Table 1 unless otherwise specified by the purchaser.

4 General Requirements for Delivery

4.1 Structural products furnished under this specification shall conform to the requirements of the current edition of Specification A6/A6M, for the specific structural product ordered, unless a conflict exists in which case this specification shall prevail.

4.2 Coils are excluded from qualification to this specification until they are processed into a finished structural product. Structural products produced from coil means structural products that have been cut to individual lengths from a coil. The processor directly controls, or is responsible for, the operations involved in the processing of a coil into a finished structural product. Such operations include decoiling, leveling or straightening, hot-forming or cold-forming (if applicable), cutting to length, testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and certification. NOTE 1—For structural products produced from coil and furnished without heat treatment or with stress relieving only, two test results are to be reported for each qualifying coil. Additional requirements regarding structural products produced from coil are described in Specification A6/A6M.

5 Bearing Plates

5.1 Unless otherwise specified, plates used as bearing plates for bridges shall be subjected to mechanical tests and shall conform to the tensile requirements of Section 8.

5.2 Unless otherwise specified, mechanical tests shall not be required for plates over 1
1
⁄2 in. [40 mm] in thickness used as bearing plates in structures other than bridges, subject to the requirement that they shall contain 0.20 to 0.33 % carbon by heat analysis, that the chemical composition shall conform to the requirements ofTable 3 in phosphorus and sulfur content, and that a sufficient discard shall be made to secure sound plates.

6 Materials and Manufacture

6.1 The steel shall be killed

7 Chemical Composition

7.1 The heat analysis shall conform to the requirements prescribed in Table 3, except as specified in 5.2.

7.2 The steel shall conform on product analysis to the requirements prescribed in Table 3, subject to the product analysis tolerances in Specification A6/A6M.

8 Tension Test

8.1 The material as represented by the test specimen, except as specified in 5.2 and 8.2, shall conform to the requirements as to the tensile properties prescribed in Table 2.

8.2 Shapes less than 1 in.
2 [645 mm
2
] in cross section and bars, other than flats, less than 1⁄2 in. [12.5 mm] in thickness or diameter need not be subjected to tension tests by the manufacturer, provided that the chemical composition used is appropriate for obtaining the tensile properties in Table 2.

9 Keywords

9.1 bars; bolted construction; bridges; buildings; carbon; plates; riveted construction; shapes; steel; structural steel; welded construction

TABLE 2 Tensile Requirements A
Plates, Shapes,B and Bars:
Tensile strength, ksi [MPa] 58–80 [400–550]
Yield point, min, ksi [MPa] 36 [250]C
Plates and Bars:D,E
Elongation in 8 in. [200 mm], min, % 20
Elongation in 2 in. [50 mm], min, % 23
Shapes:
Elongation in 8 in. [200 mm], min, % 20
Elongation in 2 in. [50 mm], min, % 21B
A See the Orientation subsection in the Tension Tests section of Specification A6/A6M.

B For wide flange shapes with flange thickness over 3 in. [75 mm], the 80 ksi [550 MPa] maximum tensile strength does not apply and a minimum elongation in 2 in. [50 mm] of 19 % applies.

C Yield point 32 ksi [220 MPa] for plates over 8 in. [200 mm] in thickness.

D Elongation not required to be determined for floor plate.

4 The last approved version of this historical standard is referenced on www.astm.org.

E For plates wider than 24 in. [600 mm], the elongation requirement is reduced two percentage points. See the Elongation Requirement Adjustments subsection under the Tension Tests section of Specification A6/A6M.

TABLE 3 Chemical Requirements NOTE 1—Where “. . .” appears in this table, there is no requirement. The heat analysis for manganese shall be determined and reported as described in the heat analysis section of Specification A6/A6M.
Product ShapesA Plates > 15-in. [380 mm] WidthB Bars; Plates # 15-in. [380 mm] WidthB
Thickness, in. [mm] All To 3⁄4[20],incl Over 3⁄4 to 11⁄2 [20 to 40], incl Over 11⁄2 to 21⁄2 [40 to 65], incl Over 21⁄2 to 4 [65 to 100], incl Over 4[100] To 3⁄4[20],incl Over 3⁄4 to 11⁄2 [20 to 40], incl Over 11⁄2 to 4[100],incl Over 4[100]
Carbon, max, % 0.26 0.25 0.25 0.26 0.27 0.29 0.26 0.27 0.28 0.29
Manganese, % ... ... 0.80-1.20 0.80-1.20 0.85-1.20 0.85-1.20 ... 0.60-0.90 0.60-0.90 0.60-0.90
Phosphorus, max, % 0.04 0.030 0.030 0.030 0.030 0.030 0.04 0.04 0.04 0.04
Sulfur, max, % 0.05 0.030 0.030 0.030 0.030 0.030 0.05 0.05 0.05 0.05
Silicon, % 0.40 max 0.40 max 0.40 max 0.15-0.40 0.15-0.40 0.15-0.40 0.40 max 0.40 max 0.40 max 0.40 max
Copper, min, % when 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20
cop per steel is specified
A Manganese content of 0.85–1.35 % and silicon content of 0.15–0.40 % is required for shapes with flange thickness over 3 in. [75 mm].
B For each reduction of 0.01 percentage point below the specified carbon maximum, an increase of 0.06 percentage point manganese above the specified maximum will be permitted, up to the maximum of 1.35 %.

SUPPLEMENTARY REQUIREMENTS

These requirements shall not apply unless specified in the order.

Standardized supplementary requirements for use at the option of the purchaser are listed in Specification A6/A6M. Those that are considered suitable for use with this specification are listed by title:

S5. Charpy V-Notch Impact Test.

S30. Charpy V-Notch Impact Test for Structural Shapes:

Alternate Core Location

S32. Single Heat Bundles

S32.1 Bundles containing shapes or bars shall be from a single heat of steel.

SUMMARY OF CHANGES

Committee A01 has identified the location of selected changes to this standard since the last issue (A36/A36M – 12) that may impact the use of this standard. (Approved Dec. 1, 2014.)

(1) Revised Table 3 to modify phosphorus and sulfur limits for plate products greater than 15 in. [380 mm] in width.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

文档天下
  • 本文由 发表于 2026年11月22日 21:44:41
  • 转载请务必保留本文链接:https://www.998pdf.com/84049.html
匿名

发表评论

匿名网友 填写信息

:?: :razz: :sad: :evil: :!: :smile: :oops: :grin: :eek: :shock: :???: :cool: :lol: :mad: :twisted: :roll: :wink: :idea: :arrow: :neutral: :cry: :mrgreen: