ASTM A403 A403M-18a Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings

文档天下 国外标准评论4阅读模式

1 Scope*

1.1 This specification covers wrought stainless steel fittings for pressure piping applications.
2

1.2 Several grades of austenitic stainless steel alloys are included in this specification Grades are designated with a prefix, WP or CR, based on the applicable ASME or MSS dimensional and rating standards, respectively.

1.3 For each of the WP stainless grades, several classes of fittings are covered, to indicate whether seamless or welded construction was utilized. Class designations are also utilized to indicate the nondestructive test method and extent of nondestructive examination (NDE). Table 1 is a general summary of the fitting classes applicable to all WP grades of stainless steel covered by this specification. There are no classes for the CR grades. Specific requirements are covered elsewhere.

1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6 This specification does not apply to cast steel fittings. Austenitic stainless steel castings are covered in Specifications A351/A351M, A743/A743M, and A744/A744M.

1.7 This international standard was developed in accordance with internationally recognized principles on standard-

ization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2 Referenced Documents

2.1 ASTM Standards:
3

A351/A351M Specification for Castings, Austenitic, for Pressure-Containing Parts

A743/A743M Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application

A744/A744M Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service

A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

A960/A960M Specification for Common Requirements for Wrought Steel Piping Fittings

E112 Test Methods for Determining Average Grain Size

E165/E165M Practice for Liquid Penetrant Examination for General Industry

2.2 ASME Standards: 4

ASME B16.9 Factory-Made Wrought Steel Butt-Welding Fittings

ASME B16.11 Forged Steel Fittings, Socket-Welding and Threaded

2.3 MSS Standards: 5

MSS SP-25 Standard Marking System for Valves, Fittings, Flanges, and Unions

MSS SP-43 Standard Practice for Light Weight Stainless Steel Butt-Welding Fittings

MSS SP-79 Socket-Welding Reducer Inserts

1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.22 on Steel Forgings and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications.

3 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards volume information, refer to the standard’s Document Summary page on the ASTM website.

Current edition approved Sept. 1, 2018. Published September 2018. Originally approved in 1956. Last previous edition approved in 2018 as A403/A403M – 18. DOI: 10.1520/A0403_A0403M-18A.

2 For ASME Boiler and Pressure Vessel Code applications see related Specification SA-403 in Section II of that Code.

4 Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Two Park Ave., New York, NY 10016-5990, http:// www.asme.org.

5 Available from Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http://www.mss-hq.com.

TABLE 1 Fitting Classes for WP Grades
Class Construction Nondestructive Examination
S Seamless None
W Welded Radiography or Ultrasonic
WX Welded Radiography
WU Welded Ultrasonic

MSS SP-83 Steel Pipe Unions, Socket-Welding and Threaded MSS SP-95 Swage(d) Nipples and Bull Plugs

MSS SP-97 Integrally Reinforced Forged Branch Outlet Fittings—Socket Welding, Threaded and Buttwelding Ends

2.4 ASME Boiler and Pressure Vessel Code: 4

Section VIII Division I

Section IX

2.5 AWS Standards: 6

A 5.4 Specification for Corrosion-Resisting Chromium and Chromium-Nickel Steel Covered Welding Electrodes

A 5.9 Specification for Corrosion-Resisting Chromium and Chromium-Nickel Steel Welding Rods and Bare Electrodes

A 5.11 Specification for Nickel and Nickel-Alloy Welding Electrodes for Shielded Metal Arc Welding

A5.14 Specification for Nickel and Nickel-Alloy Bare Welding Rods and Electrodes

2.6 ASNT: 7

SNT-TC-1A (1984) Recommended Practice for Nondestructive Testing Personnel Qualification and Certification

3 Common Requirements and Ordering Information

3.1 Material furnished to this specification shall conform to the requirements of Specification A960/A960M including any supplementary requirements that are indicated in the purchase order. Failure to comply with the common requirements of Specification A960/A960M constitutes nonconformance with this specification. In case of conflict between this specification and Specification A960/A960M, this specification shall pre-vail.

3.2 Specification A960/A960M identifies the ordering information that should be complied with when purchasing material to this specification.

4 Material

4.1 The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products that conform to the chemical requirements in Table 2. See Table 3 for a list of common names.

4.2 The steel shall be melted by one of the following processes:

4.2.1 Electric furnace (with separate degassing and refining optional),

4.2.2 Vacuum furnace, or

6 Available from American Welding Society (AWS), 550 NW LeJeune Rd., Miami, FL 33126, http://www.aws.org.

7 Available from American Society for Nondestructive Testing (ASNT), P.O. Box 28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http://www.asnt.org.

4.2.3 One of the former followed by vacuum or electroslagconsumable remelting.

4.3 If secondary melting is employed, the heat shall be defined as all ingots remelted from a primary heat.

4.4 Grain Size—Annealed Alloys UNS N08810 and UNS N08811 shall conform to an average grain size of ASTM No. 5 or coarser.

5 Manufacture

5.1 Forming—Forging or shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, machining, or by a combination of two or more of these operations. The forming procedure shall be so applied that it will not produce injurious defects in the fittings.

5.2 All fittings shall be heat treated in accordance with Section 6.

5.3 Grade WP fittings ordered as Class S shall be of seamless construction and shall meet all requirements of ASME B16.9, ASME B16.11, MSS SP-79, MSS SP-83, MSS SP-95, or MSS SP-97.

5.4 Grade WP fittings ordered as Class W shall meet the requirements of ASME B16.9 and:

5.4.1 Shall have all pipe welds made by mill or the fitting manufacturer with the addition of filler metal radiographically examined throughout the entire length in accordance with the Code requirements stated in 5.5, and,

5.4.2 Radiographic inspection is not required on single longitudinal seam welds made by the starting pipe manufacturer if made without the addition of filler metal; and

5.4.3 Radiographic inspection is not required on longitudinal seam fusion welds made by the fitting manufacturer when all of the following conditions have been met:

5.4.3.1 No addition of filler metal,

5.4.3.2 Only one welding pass per weld seam, and,

5.4.3.3 Fusion welding from one side only.

5.4.4 In place of radiographic examination, welds made by the fitting manufacturer may be ultrasonically examined in accordance with the Code requirements stated in 5.6.

5.5 Grade WP fittings ordered as Class WX shall meet the requirements of ASME B16.9 and shall have all welds, whether made by the fitting manufacturer or the starting material manufacturer, radiographically examined throughout their entire length in accordance with Paragraph UW-51 of Section VIII, Division I, of the ASME Boiler and Pressure Vessel Code.

5.6 Grade WP fittings ordered as Class WU shall meet the requirements of ASME B16.9 and shall have all welds, whether made by the fitting manufacturer or the starting material manufacturer, ultrasonically examined throughout their entire length in accordance with Appendix 12 of Section VIII, Division 1 of ASME Boiler and Pressure Vessel Code.

5.7 The radiography or ultrasonic examination of welds for this class of fittings may be done at the option of the manufacturer, either prior to or after forming.

TAB LE 2 Chem ical Req u i rements

NOTE 1 —Where an ellipsis ( . . . ) appears in this table, there is no requirement and the element need neither be analyzed for or reported.
GradeA Composition, %
Grade WP Grade CR UNS Designation CarbonB ManganeseB PhosphorousB SulphurB SiliconB Nickel Chromium Molybdenum Titanium NitrogenC Others
WPXM-19 CRXM-19 S20910 0.06 4.0-6.0 0.045 0.030 1.00 11.5-13.5 20.5-23.5 1.50-3.00 ... 0.20-0.40 E
WP20CB CR20CB N08020 0.07 2.00 0.045 0.035 1.00 32.0-38.0 19.0-21.0 2.00-3.00 ... Cu 3.0-4.0NbD 8XC min,1.00 max
WP6XN CR6XN N08367 0.030 2.00 0.040 0.030 1.00 23.5-25.5 20.0-22.0 6.0-7.0 ... 0.18-0.25 Cu 0.75
WP700 CR700 N08700 0.04 2.00 0.040 0.030 1.00 24.0-26.0 19.0-23.0 4.3-5.0 Cu 0.50NbD 8XC min
WPNIC CRNIC N08800 0.10 1.50 0.045 0.015 1.00 30.0-35.0 19.0-23.0 ... 0.15-0.60 ... Al 0.15-0.60Cu 0.75Fe 39.5 min
WPNIC10 CRNIC10 N08810 0.05-0.10 1.50 0.045 0.015 1.00 30.0-35.0 19.0-23.0 ... 0.15-0.60 ... Al 0.15-0.60Cu 0.75Fe 39.5 min
WPNIC11 CRNIC11 N08811 0.06-0.10 1.50 0.040 0.015 1.00 30.0-35.0 19.0-23.0 ... 0.15-0.60 ... Al 0.15-0.60Cu 0.75Fe 39.5 min
WP904L CR904L N08904 0.020 2.00 0.045 0.035 1.00 23.0-28.0 19.0-23.0 4.0-5.0 ... 0.10 Cu 1.0-2.0
WP1925 CR1925 N08925 0.020 1.00 0.045 0.030 0.50 24.0-26.0 19.0-21.0 6.0-7.0 0.10-0.20 Cu 0.8-1.5
WP1925N CR1925N N08926 0.020 2.00 0.030 0.010 0.50 24.0-26.0 19.0-21.0 6.0-7.0 ... 0.15-0.25 Cu 0.5-1.5
WP304 CR304 S30400 0.08 2.00 0.045 0.030 1.00 8.0-11.0 18.0-20.0 ... ... ... ...
WP304L CR304L S30403 0.030F 2.00 0.045 0.030 1.00 8.0-12.0 18.0-20.0 ... ... ... ...
WP304H CR304H S30409 0.04-0.10 2.00 0.045 0.030 1.00 8.0-11.0 18.0-20.0 ... ... ... ...
WP304N CR304N S30451 0.08 2.00 0.045 0.030 1.00 8.0-11.0 18.0-20.0 ... ... 0.10-0.16 ...
WP304LN CR304LN S30453 0.030 2.00 0.045 0.030 1.00 8.0-11.0 18.0-20.0 ... ... 0.10-0.16 ...
WP309 CR309 S30900 0.20 2.00 0.045 0.030 1.00 12.0-15.0 22.0-24.0 ... ... ... ...
WP310S CR310S S31008 0.08 2.00 0.045 0.030 1.00 19.0-22.0 24.0-26.0 ... ... ... ...
WP310H CR310H S31009 0.04-0.10 2.00 0.045 0.030 1.00 19.00-22.0 24.0-26.0 ... ... ... ...
WPS31254 CRS31254 S31254 0.020 1.00 0.030 0.010 0.80 17.5-18.5 19.5-20.5 6.0-6.5 ... 0.18-0.25 Cu 0.50-1.00
WPS31266 CRS31266 S31266 0.030 2.00-4.00 0.035 0.020 1.00 21.00-24.00 23.00-25.00 5.2-6.2 ... 0.35-0.60 Cu 1.00-2.50W 1.50-2.50
WP316 CR316 S31600 0.08 2.00 0.045 0.030 1.00 10.0-14.0 16.0-18.0 2.00-3.00 ... ... ...
WP316L CR316L S31603 0.030F 2.00 0.045 0.030 1.00 10.0-14.0G 16.0-18.0 2.00-3.00 ... ... ...
WP316H CR316H S31609 0.04-0.10 2.00 0.045 0.030 1.00 10.0-14.0 16.0-18.0 2.00-3.00 ... ... ...
WP316N CR316N S31651 0.08 2.00 0.045 0.030 1.00 10.0-13.0 16.0-18.0 2.00-3.00 ... 0.10-0.16 ...
WP316LN CR316LN S31653 0.030 2.00 0.045 0.030 1.00 10.0-13.0 16.0-18.0 2.00-3.00 ... 0.10-0.16 ...
WP317 CR317 S31700 0.08 2.00 0.045 0.030 1.00 11.0-15.0 18.0-20.0 3.0-4.0 ... ... ...
WP317L CR317L S31703 0.030 2.00 0.045 0.030 1.00 11.0-15.0 18.0-20.0 3.0-4.0 ... ... ...
WPS31725 CRS31725 S31725 0.030 2.00 0.045 0.030 1.00 13.5-17.5 18.0-20.0 4.0-5.0 ... 0.20 ...
WPS31726 CRS31726 S31726 0.030 2.00 0.045 0.030 1.00 13.5-17.5 17.0-20.0 4.0-5.0 ... 0.10-0.20 ...
WPS31727 CRS31727 S31727 0.030 1.00 0.030 0.030 1.00 14.5-16.5 17.5-19.0 3.8-4.5 ... 0.15-0.21 Cu 2.8-4.0
WPS31730 CRS31730 S31730 0.030 2.00 0.040 0.010 1.00 15.0-16.5 17.0-19.0 3.0-4.0 ... 0.045 Cu 4.0-5.0
WPS32053 CRS32053 S32053 0.030 1.00 0.030 0.010 1.00 24.0-26.0 22.0-24.0 5.0-6.0 ... 0.17-0.22 ...
WP321 CR321 S32100 0.08 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 ... H ... ...
WP321H CR321H S32109 0.04-0.10 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 ... I ... ...
WPS33228 CRS33228 S33228 0.04-0.08 1.00 0.020 0.015 0.30 31.0-33.0 26.0-28.0 ... ... ... Ce 0.05-0.10

A403/A403M - 18a

TABLE 2 Continued
GradeA Composition, %
Grade WP Grade CR UNS Designation CarbonB ManganeseB PhosphorousB SulphurB SiliconB Nickel Chromium Molybdenum Titanium NitrogenC Others
Al 0.025NbD0.6-1.0
WPS34565 CRS34565 S34565 0.030 5.0-7.0 0.030 0.010 1.00 16.0-18.0 23.0-25.0 4.0-5.0 ... 0.40-0.60 NbD0.10
WP347 CR347 S34700 0.08 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 ... ... ... J
WP347H CR347H S34709 0.04-0.10 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 ... ... ... K
WP347LN CR347LN S34751 0.005-0.020 2.00 0.045 0.030 1.00 9.0-13.0 17.0-19.0 ... ... ... NbD0.20-0.50,L N0.06-0.10C
WP348 CR348 S34800 0.08 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 ... ... ... NbD+Ta=10×(C)-1.10Ta 0.10Co 0.20
WP348H CR348H S34809 0.04-0.10 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 ... ... ... NbD+Ta=8×(C)-1.10Ta 0.10Co 0.20
WPS38815 CRS38815 S38815 0.030 2.00 0.040 0.020 5.5-6.5 15.0-17.0 13.0-15.0 0.75-1.50 ... ... Cu 0.75-1.50Al 0.30
A See Section 1 5 fo r marki ng req u i rements .
B M axi m u m , u n l ess othe rwise i nd icated .
CThe method of analysis fo r n itrogen shal l be a matte r of ag reement between the p u rchase r and man ufactu re r.
DN iobi u m and col u m bi u m are i nte rchangeable names fo r the same element and both names are acceptable fo r use i n A0 1 . 22 specifications .
E N iobi u m (col u m bi u m) 0 . 1 0–0 . 30 % ; Vanad i u m , 0 . 1 0–0 . 30 % .
F Fo r smal l d iamete r o r th i n wal ls , o r both , whe re many d rawi ng passes are req u i red , a carbon maxi m u m of 0 . 040 % is necessary i n g rades TP304 L and TP3 1 6 L. S mal l outside d iamete r tu bes are defi ned as those less than 0 . 500 i n . [ 1 2 . 7 m m] i n outside d iamete r and l i g ht wal l tu bes as those l ess than 0 . 049 i n . [ 1 . 24 m m] i n ave rage wal l th ickness .
GOn pi e rced tu bi ng , the n icke l may be 1 1 . 0–1 6 . 0 % .
H 5X (C+N) m i n–0 . 70 max.
I 4X (C+N) m i n–0 . 70 max.
JThe n iobi u m (col u m bi u m) content shal l be not l ess than ten ti mes the carbon content and not mo re than 1 . 1 0 % .
KThe n iobi u m (col u m bi u m) content shal l be not l ess than e i g ht ti mes the carbon content and not mo re than 1 . 1 0 % .
LThe n iobi u m (col u m bi u m) content shal l be not l ess than 1 5 ti mes the carbon content .

A403/A403M - 18a

TABLE 3 Common Names
Grade WPA Grade CRA UNS Designation TypeB
WPXM-19 CRXM-19 S20910 XM-19C
WP20CB CR20CB N08020 . . .
WP6XN CR6XN N08367 . . .
WP700 CR700 N08700 . . .
WPNIC CRNIC N08800 800C
WPNIC10 CRNIC10 N08810 800HC
WPNIC11 CRNIC11 N08811 . . .
WP904L CR904L N08904 904LC
WP1925 CR1925 N08925 . . .
WP1925N CR1925N N08926 . . .
WP304 CR304 S30400 304
WP304L CR304L S30403 304L
WP304H CR304H S30409 304H
WP304N CR304N S30451 304N
WP304LN CR304LN S30453 304LN
WP309 CR309 S30900 309
WP310S CR310S S31008 310S
WP310H CR310H S31009 310H
WPS31254 CRS31254 S31254 . . .
WPS31266 CRS31266 S31266 . . .
WP316 CR316 S31600 316
WP316L CR316L S31603 316L
WP316H CR316H S31609 316H
WP316N CR316N S31651 316N
WP316LN CR316LN S31653 316LN
WP317 CR317 S31700 317
WP317L CR317L S31703 317L
WPS31725 CRS31725 S31725 317LMC
WPS31726 CRS31726 S31726 317LMNC
WPS31727 CRS31727 S31727 . . .
WPS31730 CRS31730 S31730 . . .
WPS32053 CRS32053 S32053 . . .
WP321 CR321 S32100 321
WP321H CR321H S32109 321H
WPS33228 CRS33228 S33228 . . .
WPS34565 CRS34565 S34565 . . .
WP347 CR347 S34700 347
WP347H CR347H S34709 347H
WP347LN CR347LN S34751 347LN
WP348 CR348 S34800 348
WP348H CR348H S34809 348H
WPS38815 CRS38815 S38815 . . .
A Naming system developed and applied by ASTM International.
B Unless otherwise indicated, a grade designation originally assigned by the American Iron and Steel Institute (AISI).
C Common name, not a trademark widely used, not associated with any one producer.

5.8 Personnel performing NDE examinations shall be qualified in accordance with SNT-TC-1A.

5.9 Grade CR fittings shall meet the requirements of MSS SP-43 and do not require nondestructive examination.

5.10 All fittings shall have the welders, welding operators, and welding procedures qualified under the provisions of Section IX of the ASME Boiler and Pressure Vessel Code except that starting pipe welds made without the addition of filler metal do not require such qualification.

5.11 All joints welded with filler metal shall be finished in accordance with the requirements of Paragraph UW-35 (a) of Section VIII, Division I, of the ASME Boiler and Pressure Vessel Code.

5.12 Fittings machined from bar shall be restricted to NPS 4 or smaller. Elbows, return bends, tees, and header tees shall not be machined directly from bar stock.

5.12.1 All caps machined from bar shall be examined by liquid penetrant in accordance with Supplementary Requirement S52 in Specification A960/A960M.

5.13 Weld buildup is permitted to dimensionally correct unfilled areas produced during cold forming of stub ends. Radiographic examination of the weld buildup shall not be required provided that all the following steps are adhered to:

5.13.1 The weld procedure and welders or welding operators meet the requirements of 5.10.

5.13.2 Annealing is performed after welding and prior to machining.

5.13.3 All weld surfaces are liquid penetrant examined in accordance with Appendix 8 of Section VIII, Division 1 of the ASME Boiler and Pressure Vessel Code.

5.13.4 Repair of areas in the weld is permitted, but 5.13.1, 5.13.2, and 5.13.3 must be repeated.

5.14 Stub ends may be produced with the entire lap added as weld metal to a straight pipe section provided the welding satisfies the requirements of 5.10 for qualifications and Section 6 for post weld heat treatment.

5.14.1 Grade WP Class W—Radiographic inspection of the weld is required. See 5.4.

5.14.2 Grade WP Class WX—Radiographic inspection of all welds is required. See 5.5.

5.14.3 Grade WP Class WU—Ultrasonic inspection of all welds is required. See 5.6.

5.14.4 Grade CR—Nondestructive examination is not required. See 5.12.1.

5.15 Stub ends may be produced with the entire lap added by the welding of a ring, made from plate or bar of the same alloy grade and composition, to the outside of a straight section of pipe, provided the weld is double welded, is a full penetration joint, satisfies the requirements of 5.10 for qualifications and Section 6 for post weld heat treatment.

5.15.1 Grade WP Class W—Radiographic inspection of the welds, made with the addition of filler metal, is required (see 5.4).

5.15.2 Grade WP Class WX—Radiographic inspection of all welds, made with or without the addition of filler metal, is required (see 5.5).

5.15.3 Grade WP Class WU—Ultrasonic inspection of all welds, made with or without the addition of filler metal, is required (see 5.6).

5.15.4 Grade CR nondestructive examination is not required (see 5.9).

5.16 After final heat treatment, all “H-Grade” steel fittings shall have a grain size of 7 or coarser in accordance with Test Methods E112.

6 Heat Treatment

6.1 All fittings shall be furnished in the heat-treated condition. For H grades, separate solution heat treatments are required for solution annealing; in-process heat treatments are not permitted as a substitute for the separate solution annealing treatments. The heat-treat procedure, except for those grades listed in 6.2, shall consist of solution annealing the fittings at the temperatures listed for each grade in Table 4 until the

TABLE 4 Heat Treatment
GradeWPAA GradeCRA UNS Designation Solution AnnealTemperature, min °F [°C]B Quench Media
WPXM-19 CRXM-19 S20910 1900 [1040] water or other rapid cool
WP20CB CR20CB N08020 1700-1850[927-1010] water or other rapid cool
WP6XN CR6XN N08367 2025 [1107] water or other rapid cool
WP700 CR700 N08700 2025-2100[1107-1150] water or other rapid cool
WPNIC CRNIC N08800 1800-1900[983-1038]C water or other rapid cool
WPNIC10 CRNIC10 N08810 2100-2150[1147-1177]C water or other rapid cool
WPNIC11 CRNIC11 N08811 2100-2150[1147-1177]C water or other rapid cool
WP904L CR904L N08904 1985-2100[1085-1150] water or other rapid cool
WP1925 CR1925 N08925 1800-1900[983-1038] water or other rapid cool
WP1925N CR1925N N08926 2150 [1177] water or other rapid cool
WP304 CR304 S30400 1900 [1040] water or other rapid cool
WP304L CR304L S30403 1900 [1040] water or other rapid cool
WP304H CR304H S30409 1900 [1040] water or other rapid cool
WP304N CR304N S30451 1900 [1040] water or other rapid cool
WP304LN CR304LN S30453 1900 [1040] water or other rapid cool
WP309 CR309 S30900 1900 [1040] water or other rapid cool
WP310S CR310S S31008 1900 [1040] water or other rapid cool
WP310H CR310H S31009 1900 [1040] water or other rapid cool
WPS31254 CR31254 S31254 2100 [1150] water or other rapid cool
WPS31266 CRS31266 S31266 2100 [1150] water or other rapid cool
WP316 CR316 S31600 1900 [1040] water or other rapid cool
WP316L CR316L S31603 1900 [1040] water or other rapid cool
WP316H CR316H S31609 1900 [1040] water or other rapid cool
WP316N CR316N S31651 1900 [1040] water or other rapid cool
WP316LN CR316LN S31653 1900 [1040] water or other rapid cool
WP317 CR317 S31700 1900 [1040] water or other rapid cool
WP317L CR317L S31703 1900 [1040] water or other rapid cool
WPS31725 CRS31725 S31725 1900 [1040] water or other rapid cool
WPS31726 CRS31726 S31726 1900 [1040] water or other rapid cool
WPS31727 CRS31727 S31727 1975-2155[1080-1180] water or other rapid cool
WPS31730 CRS31730 S31730 1900 [1040] water or other rapid cool
WPS32053 CRS32053 S32053 1975-2155[1080-1180] water or other rapid cool
WP321 CR321 S32100 1900 [1040] water or other rapid cool
WP321H CR321H S32109 1925 [1050] water or other rapid cool
WPS33228 CRS33228 S33228 2050-2160[1120-1180] water or other rapid cool
WPS34565 CRS34565 S34565 2050-2140[1120-1170] water or other rapid cool
WP347 CR347 S34700 1900 [1040] water or other rapid cool
WP347H CR347H S34709 1925 [1050] water or other rapid cool
WP347LN CR347LN S34751 1900 [1040] water or other rapid cool
WP348 CR348 S34800 1900 [1040] water or other rapid cool
WP348H CR348H S34809 1925 [1050] water or other rapid cool
WPS38815 CRS38815 S38815 1950 [1065] water or other rapid cool
A Naming system developed and applied by ASTM International.
B Where a range of temperature is not listed, the single value shown shall be the minimum required temperature.
C Heat Treatment is highly dependent on intended service temperature; consult material manufacturer for specific heat treatments for end use temperature.

chromium carbides go into solution, and then cooling at a sufficient rate to prevent reprecipitation.

6.2 A solution annealing temperature above 1950 °F [1065 °C] may impair the resistance to intergranular corrosion after subsequent exposure to sensitizing conditions in 321, 321H, 347, and 347H. When specified by the purchaser a lower temperature stabilizing treatment or a second solution anneal shall be used subsequent to the initial high-temperature solution anneal (see Supplementary Requirement S2).

6.3 All welding shall be done prior to heat treatment.

6.4 Fittings machined directly from solution-annealed forgings and bar stock need not be annealed again.

7 Chemical Composition

7.1 The chemical composition of each cast or heat used shall be determined and shall conform to the requirements of the chemical composition for the respective grades of materials listed in Table 2. The ranges as shown have been expanded to include variations of the chemical analysis requirements that are listed in the various specifications for starting materials (pipe, tube, plate, bar, and forgings) normally used in the manufacturing of fittings to this specification. Methods and practices relating to chemical analyses required by this specification shall be in accordance with Test Methods, Practices, and Terminology A751. Product analysis tolerances in accordance with Specification A960/A960M are applicable.

7.2 The steel shall not contain any unspecified elements for the ordered grade to the extent that it conforms to the requirements of another grade for which that element is a specified element having a required minimum content.

7.3 In fittings of welded construction, the alloy content (carbon, chromium, nickel, molybdenum, niobium (columbium), and tantalum) of the deposited weld metal shall conform to that required of the base metal or for equivalent weld metal as given in the AWS filler metal specification A 5.4 or A 5.9 (Type 348 weld metal is listed in AWS A 5.9 but not in AWS A 5.4). Exceptions are when welding on Types 304L and 304 base metals, the deposited weld metal shall correspond, respectively, to AWS E308L (ER308L) and E308 (ER308). When welding 310S or 310H, the weld metal shall correspond to AWS ER310 unless otherwise advised by the purchaser at the time of placement on the purchase order. When welding on Type 321 base metal, the weld metal shall correspond to AWS Type E347 (ER347 or ER321); and, when welding on S31725, S31726, S31254, S31266, or S33228 deposited weld metal shall correspond either to the alloy content of the base metal or to AWS A5.11 E NiCrMo·3 (UNS W86112) (AWS A5.14 Ni Cr Mo·3 (UNS N06625)), and when welding on S31730, deposited weld metal and filler metal used shall correspond either to the alloy content of the base metal or to AWS A5.14 ERNiCr-3 (UNS N06082), or ERNiCrMo-3 (UNS N06625), or ERNiCrMo-4 (UNS N10276). On S38815 base metals, the deposited weld metal and filler metal used shall be agreed upon between purchaser and manufacturer. In fittings of welded construction made from predominantly ferrous alloys N08020, N08367, N08700, N08800, N08810, N08811, N08904, N08925 & N08926, the alloy content of the deposited weld metal shall conform to that required of the base metal or for the equivalent weld metal given in the AWS Filler Metal Specification A5.11 and A5.14. However, it is possible that weld deposit chemistry will not meet the limits of either the base metal or the filler metal for some elements. The weld deposit chemistry shall meet the lowest minimum and highest maximum values for each specification element in either of the base metal or filler metal specification. Dilution of the base and filler metal must be considered when determining weld deposit criteria for over-alloyed filler metals.

7.3.1 Supplementary Requirement S1 may be specified where 16-8-2 filler metal is required for joining thick sections of Types 316, 321, or 347 and has adequate corrosion resistance for the intended service.

8 Tensile Properties

8.1 The tensile properties of the fitting material shall conform to the requirements of Table 5. The testing and reporting shall be performed in accordance with Specification A960/ A960M.

TABLE 5 Tensile Requirements
All WP and CR Grades Yield Strength, min, ksi [MPa] Tensile Strength, min, ksi [MPa]
304, 304LN, 304H, 309, 310S, 310H, 316, 316LN, 316H, 317, 317L, 347, 347H, 347LN, 348, 348H 30 [205] 75 [515]
321, 321H
Seamless (A312 tubular):
t ≤ 3/8 in. 30 [205] 75 [515]
t > 3/8 in. 25 [170] 70 [485]
All other fitting classes: 30 [205] 75 [515]
S31266 61 [420] 109 [750]
S31725
S31727 36 [245] 80 [550]
S31730 25 [175] 70 [480]
S32053 43 [295] 93 [640]
304L, 316L 25 [170] 70 [485]
304N, 316N, S31726 35 [240] 80 [550]
XM-19 55 [380] 100 [690]
N08020 35 [240] 80 [550]
N08367 45 [310] 95 [655]
N08700 35[240] 80[550]
N08800 25 [205] 65 [520]
N08810 25 [170] 65 [450]
N08811 25 [170] 65 [450]
N08904 31 [220] 71 [490]
N08925 43[295] 87 [600]
N08926 43 [295] 94 [650]
S31254 44 [300] 94 [650] to 119 [820]
S33228 27 [185] 73 [500]
S34565 60 [415] 115 [795]
S38815 37 [255] 78 [540]
Elongation Requirements
Longitudinal Transverse
Standard round specimen, or small proportional specimen, or strip-type specimen, minimum % in 4 DA 28 20
A S38815 Elongation in 2 in. — 30 % min.

8.1.1 Specimens cut either longitudinally or transversely shall be acceptable for the tensile test.

8.1.2 While Table 5 specifies elongation requirements for both longitudinal and transverse specimens, it is not the intent that both requirements apply simultaneously. Instead, it is intended that only the elongation requirement that is appropriate for the specimen used be applicable.

8.2 Records of the tension test made on the starting material shall be certification that the material of the fitting meets the requirements of this specification provided that heat treatments are the same.

8.3 If the raw material was not tested, or if the heat treatment of the raw material was different than the heat treatment of the fitting, the fitting manufacturer shall perform at least one tension test per heat on material representative of the fitting, and in the same condition of heat treatment as the fitting it represents. Qualification of welding procedures shall be in accordance with 5.8.

8.4 If a tension test through the weld is desired, Supplementary Requirement S51 in Specification A960/A960M should be specified.

9 Hydrostatic Tests

9.1 Hydrostatic testing is not required by this specification.

9.2 All Grade WP fittings shall be capable of withstanding without failure, leakage, or impairment of serviceability, a test pressure equal to that prescribed for the specified matching pipe or equivalent material.

9.3 All Grade CR fittings, except tees covered in 9.3.1, shall be capable of withstanding without failure, leakage, or impairment of serviceability, a test pressure based on the ratings in MSS SP-43.

9.3.1 Grade CR tees fabricated using intersection welds shall be capable of passing a hydrostatic test based on 70 % of the ratings in MSS SP-43.

10 Surface Finish, Appearance, and Corrosion Protection

10.1 The requirements of Specification A960/A960M apply except as modified as follows:

10.2 Fittings supplied under this specification shall be examined visually. Selected typical surface discontinuities shall be explored for depth. The fittings shall be free from surface discontinuities that penetrate more than 5 % of the specified nominal wall thickness, except as defined in 10.4 and 10.5, and shall have a workmanlike finish.

10.3 Surface discontinuities deeper than 5 % of the specified nominal wall thickness, except as defined in 10.4 and 10.5, shall be removed by the manufacturer by machining or grinding to sound metal, and the repaired areas shall be well faired. The wall thickness at all points shall be at least 87
1
⁄2 % of the specified nominal wall thickness, and the diameters at all points shall be within the specified limits.

10.4 Surface checks (fish scale) deeper than 1
⁄64 in. [0.4 mm] shall be removed.

10.5 Mechanical marks deeper than 1
⁄16 in. [1.6 mm] shall be removed.

10.6 When the removal of a surface discontinuity reduces the wall thickness below 87
1
⁄2 % of the specified nominal wall thickness at any point, the fitting shall be subject to rejection or to repair as provided in Section 11.

11 Repair by Welding

11.1 Repair of unacceptable imperfections in the base metal is permissible for fittings made to the dimensional standards listed in 1.1 or for other standard fittings made for stock by the manufacturer. Prior approval of the purchaser is required to repair special fittings made to the purchaser’s requirements. Welding of unacceptable imperfections in no case shall be permitted when the depth of defect exceeds 33
1
⁄3 % of the nominal wall thickness or the defect area exceeds 10 % of the surface area of the fitting.

11.2 The welding procedure and welders shall be qualified in accordance with Section IX of the ASME Boiler and Pressure Vessel Code.

11.3 The composition of the weld deposits shall be in accordance with 7.3 and in accordance with the procedure qualification for the applicable material.

11.4 Unacceptable imperfections shall be removed by mechanical means or by thermal cutting or gouging methods. Cavities prepared for welding shall be examined with liquid penetrant in accordance with Practice E165/E165M. No cracks are permitted in the prepared cavities. Personnel performing NDE examinations shall be qualified in accordance with SNT-TC-1A

11.5 The weld repair shall be permanently identified with the welder’s stamp or symbol in accordance with Section VIII of the ASME Boiler and Pressure Vessel Code.

11.6 Weld repair area(s) shall be blended uniformly to the base metal and shall be examined by liquid penetrant in accordance with Practice E165/E165M. No cracks are permitted in the weld or surrounding 1⁄2 in. [12.7 mm] of base metal. Personnel performing NDE examinations shall be qualified in accordance with SNT-TC-1A.

11.7 After weld repair, material shall be heat treated in accordance with Section 6.

11.8 The fittings shall be free of scale and shall be passivated.

12 Dimensions

12.1 For fittings covered by ASME B16.9, ASME B16.11, MSS SP-43, MSS SP-79, MSS SP-83, MSS SP-95, or MSS SP-97, the sizes, shapes, and dimensions of the fittings shall be as specified in those standards.

12.1.1 Fittings of size or shape differing from these standards, but meeting all other requirements of this specification, may be furnished in accordance with Supplementary Requirement S58 Specification A960/A960M.

13 Rejection and Rehearing

13.1 Material that fails to conform to the requirements of this specification may be rejected. Rejection should be reported to the producer or supplier promptly and in writing. In case of dissatisfaction with the results of the tests, the producer or supplier may make claim for rehearing.

13.2 Fittings that develop defects in shop working or application operations may be rejected. Upon rejection, the manufacturer shall be notified promptly in writing.

14 Certification

14.1 Test reports are required for all fittings covered by this specification. Each test report shall meet the requirements for certification in Specification A960/A960M as well as include the following information specific to this specification:

14.1.1 Chemical analyses results for all starting materials, Section 7 (Table 2), reported results shall be to the same number of significant figures as the limits specified in Table 2 for that element,

14.1.2 Tensile property results of all starting materials, Section 8 (Table 5), report the yield strength and the tensile strength in ksi [MPa] and elongation in percent,

14.1.3 For construction with filler metal added, weld metal chemical analysis,

14.1.4 For welded fittings, construction method, weld process and procedure specification number,

14.1.5 Type heat treatment, Section 6 (Table 4),

14.1.6 Results of all nondestructive examinations, and

14.1.7 Any supplementary testing required by the purchase order.

15 Product Marking

15.1 In addition to marking requirements of Specification A960/A960M, the following additional marking requirements shall apply:

15.1.1 All fittings shall have the prescribed information stamped or otherwise suitably marked on each fitting. See Table 6 for marking examples of grades and classes.

15.1.2 Marking paint or ink shall not contain harmful amounts of chlorides, metals, or metallic salt, such as zinc or

TABLE 6 Product Marking Examples for Grades and Classes
Grade and Class Marking Description
CR304 Single grade: No classes in CR grades
CR304/304L Multiple grades, meet chemical and mechanical properties of each
WP304-S Single Grade: seamless
WP304-W Single Grade; welded: RT or UT pipe welds with filler metal and all fitting manufacturer's welds
WP304-WX Single grade: welded: RT all welds with or without filler metal
WP304-WU Single grade; welded: UT all welds with or without filler metal
WP304-304L-S Multiple grades: meet chemical and mechanical properties of each: seamless

copper, that cause corrosive attack on heating. On wall thicknesses thinner than 0.083 in. [2.1 mm], no metal impression stamps shall be used. Vibrating pencil marking is acceptable.

15.1.3 Threaded or socket-welding fittings shall be additionally marked with the pressure class. Plugs and bushings furnished to ASME B16.11 requirements are not required to be marked. The class S marking need not be added to the material grade for threaded or socket-welded fittings.

15.1.4 When agreed upon between the purchaser and producer, and specified in the order, the markings shall be painted or stenciled on the fitting or stamped on a metal or plastic tag which shall be securely attached to the fitting.

15.1.5 Fittings meeting the chemical and mechanical property requirements of Table 2 and Table 5 for more than one grade designation may be marked with more than one class or grade designation, such as WP304/304H; WP304/304L; WP304/304L/304N, WP316/316L, etc.

15.2 Bar Coding—In addition to the requirements in 15.1, bar coding is acceptable as a supplemental identification method. The purchaser may specify in the order a specific bar coding system to be used. The bar coding system, if applied at the discretion of the supplier, should be consistent with one of the published industry standards for bar coding. If used on small fittings, the bar code may be applied to the box or a substantially applied tag.

16 Keywords

16.1 austenitic stainless steel; corrosive service applications; pipe fittings; steel; piping applications; pressure containing parts; stainless steel fittings

SUPPLEMENTARY REQUIREMENTS

One or more of the supplementary requirements described below or appearing in Specification A960/A960M may be included in the order or contract. When so included, a supplementary requirement shall have the same force as if it were in the body of the specification. Supplementary requirement details not fully described shall be agreed upon between the purchaser and the supplier.

S1. Special Filler Metal

S1.1 Filler metal shall be AWS Type E16-8-2 or ER 16-8-2 (AWS Specifications A 5.4 and A 5.9, respectively). Fittings welded with 16-8-2 weld metal shall be marked WP ___ HRW or CR ___ HRW, as appropriate.

S2. Stabilizing Treatment

S2.1 Subsequent to the solution anneal required by 6.2, Grades 321, 321H, 347, 347H, 348, and 348H shall be given a stabilizing treatment at 1500 to 1600 °F [815 to 870 °C] for a

minimum of 2 h/in. [4.7 min/mm] of thickness and then cooling in the furnace or in air. In addition to the marking required in Section 15, the grade designation symbol shall be followed by the symbol “S2.”

Committee A01 has identified the location of selected changes to this specification since the last issue, A403/A403M – 18, that may impact the use of this specification. (Approved Sept. 1, 2018)

(1) Replaced 310H back into specification.

Committee A01 has identified the location of selected changes to this specification since the last issue, A403/A403M – 16, that may impact the use of this specification. (Approved March 1, 2018)

(1) Interchangeable use of Niobium (Columbium) is addressed in Table 2 and Section 7 as a pattern for all A01.22 specifications.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

资源下载此资源下载价格为5金币立即购买,VIP免费

1.本站大部份文档均属免费,部份收费文档,经过本站分类整理,花了精力和时间,收费文档是为了网站运营成本等费用开支;
2.购买会员:全部免费下载本站资源(或单次下载)即视为对网站的赞助、打赏,非商业交易行为(不认同此观点请勿支付)请慎重考虑;
3.所有收费文档都真实可靠,为了节约成本,文档在网站前台不做预览,如果付费后,与实际文档不符合,都可以加微信号:pdftj888申请退款;
4.付费下载过程中,如果遇到下载问题,都可以加微信号pdftj888解决;
5.手机支付,尽量选择支付宝支付;
6.如图集或者标准不清楚,在本站找不到您需要的规范和图集,希望增加资料等任何问题,可联系微信号:pdftj888解决;

文档天下
  • 本文由 发表于 2026年11月22日 21:41:55
  • 转载请务必保留本文链接:https://www.998pdf.com/84047.html
匿名

发表评论

匿名网友 填写信息

:?: :razz: :sad: :evil: :!: :smile: :oops: :grin: :eek: :shock: :???: :cool: :lol: :mad: :twisted: :roll: :wink: :idea: :arrow: :neutral: :cry: :mrgreen: