ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule

文档天下 国外标准评论1阅读模式

1 Scope*

1.1 This specification covers poly(vinyl chloride) (PVC) Schedule 80 pipe fittings. Included are requirements for materials, workmanship, dimensions, and burst pressure.

NOTE 1—CPVC plastic pipe fittings, which were formerly included in this standard, are now covered in Specification F439.

1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases, some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing.

NOTE 2—Pressurized (compressed) air or other compressed gases contain large amounts of stored energy, which present serious safety hazards should a system fail for any reason.

1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2 Referenced Documents

2.1 ASTM Standards:
2

D618 Practice for Conditioning Plastics for Testing

D1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings

D1600 Terminology for Abbreviated Terms Relating to Plastics

D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120

D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

D2749 Symbols for Dimensions of Plastic Pipe Fittings F412 Terminology Relating to Plastic Piping Systems

F439 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80

F1498 Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings

2.2 Federal Standard:
3

Fed. Std. No. 123 Marking for Shipment (Civil Agencies)

2.3 National Sanitation Foundation Standards:
4

Standard No. 14 for Plastic Piping Components and Related Materials

Standard No. 61 for Drinking Water Systems Components— Health Effects

3 Terminology

3.1 General—Definitions are in accordance with Terminology F412 and abbreviations are in accordance with Terminology D1600, unless otherwise indicated. The abbreviation for poly(vinyl chloride) plastic is PVC.

1 This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.

2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards volume information, refer to the standard’s Document Summary page on the ASTM website.

Current edition approved March 1, 2015. Published March 2015. Originally approved in 1965. Last previous edition approved in 2013 as D2467 – 13a. DOI: 10.1520/D2467-15

3 DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA 19111-5094 http://quicksearch.dla.mil/

4 Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.

4 Classification

4.1 General—This specification covers Schedule 80 PVC pipe fittings, socket-type, made from four PVC plastic compounds and intended for use with Iron Pipe Size (IPS) outside-diameter plastic pipe. (See Specification D1785.)

4.1.1 Fittings covered by this specification are normally molded. In-line fittings, such as couplings, unions, bushings, caps, nipples, and the like, shall be molded or machined from extruded stock.

4.1.2 Fittings fabricated by back welding or butt fusion are not included in this specification.

5 Materials and Manufacture

5.1 This specification covers PVC pipe fittings made from five PVC plastics as classified in Specification D1784. These are PVC 12454, 11443, and 14333.

5.2 Compound—The PVC plastic compound shall meet the requirements of PVC 12454, 11443, or 14333, as described in Specification D1784.

5.3 Rework Material—The manufacturers shall use only their own clean rework fitting material and the fittings produced shall meet all the requirements of this specification.

6 Requirements

6.1 Dimensions and Tolerances:

6.1.1 Fitting sockets inside diameters (waterways), minimum wall thicknesses, and dimensions shall be as shown in-` Tables 1-5 when measured in accordance with Test Method,,, D2122., ```

6.1.2 When multistep reducer bushings are cored out, the,, inner socket shall be reinforced from the outer wall by a``, minimum of three ribs extending from the top of the inner-- socket to the deepest extremity of the coring. The transition,, , from D to DJ (Table 4) shall be straight, tapered as shown, or, `-- radiused. A positive taper in the same direction of the taper in the socket on the outside diameter of the bushing is optional (see XA/XB in Table 3). Any point measured along the outside diameter of the bushing (between points XA and XB) shall not fall below minimum pipe OD.

6.1.3 The minimum wall thickness of fittings shall be 125 % of the minimum wall thickness of the corresponding size of Schedule 80 pipe for which they are designed to be used, except that for the socket, the wall thickness shall be at least equal to the minimum wall thickness of the corresponding size of Schedule 80 pipe.

6.1.4 The minimum inside diameter of the fittings shall be not less than the minimum specified inside diameter of the corresponding size of Schedule 80 pipe. This is calculated as follows:

(minimum OD) -2 × (maximumwall) = minimum ID(1)

6.1.5 Minimum dimensions have zero negative tolerance. Tolerances on other dimensions are shown in Table 1 and Table 3.

6.2 Threads—For all fittings having taper pipe threads, threads shall conform to Specification F1498 and be gaged in accordance with 8.4.

6.3 Burst Pressure:

6.3.1 The minimum burst strength of the fittings shall be not less than that calculated for the size and wall thickness of the pipe with which it is to be used, when calculated from the following equation and using a stress of 6400 psi for 8-in. and smaller fittings, and a stress of 5100 psi for fittings larger than 8-in. when the cell class is 12454, 13354 and 11443. When the cell class is 14333 a stress of 5000 psi is used in the equation for fittings 8-in. and smaller:

S = P (Do - t ) /2t(2)

S 5 hoop stress, psi ~MPa!

P = internal pressure, psi (MPa),

Do = average outside diameter, in. (mm), and

t = minimum wall thickness, in. (mm)

Fittings tested in accordance with 8.5 shall withstand the minimum burst pressure shown in Table 6.

6.3.2 Pressures shown are minimum burst pressures and do not imply rated working pressures. The burst pressure shall be used only as an indication of quality.

7 Workmanship, Finish, and Appearance

7.1 The fittings shall be homogeneous throughout and free of cracks, holes, foreign inclusions, or other defects. The fittings shall be as uniform as commercially practicable in color, opacity, density, and other physical properties.

8 Test Methods

8.1 Conditioning—Condition the test specimens at 73.4 ± 3.6°F (23±2°C) and 50 ±10 % relative humidity for not less than 40 h prior to test in accordance with Procedure A of Practice D618, for those tests where conditioning is required.

8.2 Test Conditions—Conduct tests in the Standard Laboratory Atmosphere of 73.4 ±3.6°F (23 ±2°C) and 50 ± 5 % relative humidity, unless otherwise specified in the test methods or in this specification.

8.3 Sampling—A sufficient quantity of fittings as agreed upon between the seller and the purchaser shall be selected at random from each lot or shipment and tested to determine that the basic design is in conformance with this specification. NOTE 3—For individual orders or specifications where supplemental tests are required, only those tests and numbers of tests specifically agreed upon between purchaser and seller need be conducted.

8.4 Threads—All taper pipe threads shall be gaged in accordance with Specification F1498.

8.5 Burst Pressure—Determine the minimum burst pressure in accordance with Test Method D1599, Procedure B. The pressure shall be applied at a uniform rate such that the minimum allowable burst pressure is attained in 60 to 70 s.

9 Retest and Rejection

9.1 If the results of any test(s) do not meet the requirements of this specification, the tests(s) shall be conducted again only by agreement between the purchaser and seller. Under such agreement, minimum requirements shall not be lowered, changed, or modified, nor shall specification limits be changed.

ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
TAB LE 1 Tapered Sockets for PVC Pi pe Fitti ngs, Sched u le 80, i n . (m m)A
Nomi nal Socket A Entrance Diam eter Socke B t Bottom Diame ter CB DC Wall Thick ness, min Entrance, mi n
Pipe Size Diameter TolNeoramnicnealon Diameter Max Out-of-Round Diameter TolNeoramnicnealon Diameter Max Out-of-Round Socket Length , min I nside mDiinameter, E F EW EX EZ
1⁄8 0.41 7 (1 0.59) ±0.004 (0. 1 0) 0.01 6 (0.41 ) 0.401 (1 0. 1 8) ±0.004 (0. 1 0) 0.01 6 (0.41 ) 0.500 (1 2.7) 0. 1 71 (4.34) 0.095 (2.41 ) 0. 1 1 8 (3.00) 1⁄64 (0.40) 1⁄64 (0.40) 1⁄64 (0.40)
1⁄4 0.552 (1 4.02) ±0.004 (0. 1 0) 0.01 6 (0.41 ) 0.536 (1 3.61 ) ±0.004 (0. 1 0) 0.01 6 (0.41 ) 0.625 (1 5.88) 0.258 (6.55) 0. 1 1 9 (3.02) 0. 1 49 (3.78) 1⁄64 (0.40) 1⁄64 (0.40) 1⁄64 (0.40)
3⁄8 0.687 (1 7.45) ±0.004 (0. 1 0) 0.01 6 (0.41 ) 0.671 (1 7.04) ±0.004 (0. 1 0) 0.01 6 (0.41 ) 0.750 (1 9.05) 0.379 (9.63) 0. 1 26 (3.20) 0. 1 60 (4.06) 1⁄32 (0.79) 1⁄32 (0.79) 1⁄32 (0.79)
1⁄2 0.848 (2 1 .54) ±0.004 (0. 1 0) 0.01 6 (0.41 ) 0.836 (2 1 .23) ±0.004 (0. 1 0) 0.01 6 (0.41 ) 0.875 (22.22) 0.502 (1 2.75) 0. 1 47 (3.73) 0. 1 85 (4.70) 1⁄32 (0.79) 1⁄32 (0.79) 1⁄32 (0.79)
3⁄4 1 .058 (26.87) ±0.004 (0. 1 0) 0.020 (0.5 1 ) 1 .046 (26.57) ±0.004 (0. 1 0) 0.020 (0.5 1 ) 1 .000 (25.40) 0.698 (1 7.73) 0. 1 54 (3.9 1 ) 0. 1 95 (4.95) 1⁄32 (0.79) 1⁄32 (0.79) 1⁄32 (0.79)
1 1 .325 (33.65) ±0.005 (0. 1 3) 0.020 (0.5 1 ) 1 .31 0 (33.27) ±0.005 (0. 1 3) 0.020 (0.5 1 ) 1 . 1 25 (28.58) 0.9 1 1 (23. 1 4) 0. 1 79 (4.55) 0.225 (5.72) 1⁄1 6 (1 .59) 1⁄1 6 (1 .59) 1⁄1 6 (1 .59)
1 1⁄4 1 .670 (42.42) ±0.005 (0. 1 3) 0.024 (0.61 ) 1 .655 (42.04) ±0.005 (0. 1 3) 0.024 (0.61 ) 1 .250 (31 .75) 1 .227 (31 . 1 7) 0. 1 9 1 (4.85) 0.239 (6.07) 1⁄1 6 (1 .59) 1⁄1 6 (1 .59) 1⁄1 6 (1 .59)
1 1⁄2 1 .9 1 2 (48.56) ±0.006 (0. 1 5) 0.024 (0.61 ) 1 .894 (48. 1 1 ) ±0.006 (0. 1 5) 0.024 (0.61 ) 1 .375 (34.93) 1 .446 (36.73) 0.200 (5.08) 0.250 (6.35) 1⁄1 6 (1 .59) 1⁄1 6 (1 .59) 1⁄1 6 (1 .59)
2 2.387 (60.63) ±0.006 (0. 1 5) 0.024 (0.61 ) 2.369 (60. 1 7) ±0.006 (0. 1 5) 0.024 (0.61 ) 1 .500 (38. 1 0) 1 .881 (47.78) 0.2 1 8 (5.54) 0.275 (6.99) 1⁄1 6 (1 .59) 1⁄1 6 (1 .59) 1⁄1 6 (1 .59)
21⁄2 2.889 (73.38) ±0.007 (0. 1 8) 0.030 (0.76) 2.868 (72.85) ±0.007 (0. 1 8) 0.030 (0.76) 1 .750 (44.45) 2.250 (57. 1 5) 0.276 (7.01 ) 0.345 (8.76) 3⁄32 (2.38) 1⁄8 (3. 1 8) 1⁄8 (3. 1 8)
3 3.5 1 6 (89.31 ) ±0.008 (0.20) 0.030 (0.76) 3.492 (88.70) ±0.008 (0.20) 0.030 (0.76) 1 .875 (47.63) 2.820 (71 .63) 0.300 (7.62) 0.375 (9.53) 3⁄32 (2.38) 1⁄8 (3. 1 8) 1⁄8 (3. 1 8)
31⁄2 4.01 6 (1 02.01 ) ±0.008 (0.20) 0.030 (0.76) 3.992 (1 01 .4) ±0.008 (0.20) 0.030 (0.76) 2. 1 25 (53.98) 3.280 (83.31 ) 0.31 8 (8.08) 0.400 (1 0. 1 6) 3⁄32 (2.38) 1⁄8 (3. 1 8) 1⁄8 (3. 1 8)
4 4.5 1 8 (1 1 4.76) ±0.009 (0.23) 0.030 (0.76) 4.49 1 (1 1 4. 1 ) ±0.009 (0.23) 0.030 (0.76) 2.250 (57. 1 5) 3.737 (94.92) 0.337 (8.56) 0.420 (1 0.67) 3⁄32 (2.38) 1⁄8 (3. 1 8) 1⁄8 (3. 1 8)
5 5.583 (1 41 .81 ) ±0.01 0 (0.25) 0.060 (1 .52) 5.553 (1 41 .0) ±0.01 0 (0.25) 0.060 (1 .52) 2.625 (66.68) 4.703 (1 1 9.46) 0.375 (9.53) 0.470 (1 1 .94) 3⁄32 (2.38) 1⁄8 (3. 1 8) 1⁄8 (3. 1 8)
6 6.647 (1 68.83) ±0.01 1 (0.28) 0.060 (1 .52) 6.61 4 (1 68.0) ±0.01 1 (0.28) 0.060 (1 .52) 3.000 (76.20) 5.646 (1 43.41 ) 0.432 (1 0.97) 0.540 (1 3.72) 1⁄8 (3. 1 8) 3⁄1 6 (4.76) 3⁄1 6 (4.76)
8 8.655 (2 1 9.84) ±0.01 5 (0.38) 0.090 (2.29) 8.61 0 (2 1 8.7) ±0.01 5 (0.38) 0.090 (2.29) 4.000 (1 01 .60) 7.490 (1 90.25) 0.500 (1 2.70) 0.625 (1 5.88) 1⁄8 (3. 1 8) 3⁄1 6 (4.76) 3⁄1 6 (4.76)
1 0 1 0.780 (273.81 ) ±0.01 5 (0.38) 0. 1 00 (2.54) 1 0.735 (272.67) ±0.01 5 (0.38) 0. 1 00 (2.54) 5.000 (1 27.00) 9.407 (238.94) 0.593 (1 5.06) 0.741 (1 8.82) 1⁄8 (3. 1 8) 3⁄1 6 (4.76) 3⁄1 6 (4.76)
1 2 1 2.780 (324.61 ) ±0.01 5 (0.38) 0. 1 20 (3.05) 1 2.735 (323.47) ±0.01 5 (0.38) 0. 1 20 (3.05) 6.000 (1 52.40) 1 1 . 1 97 (284.40) 0.687 (1 7.45) 0.859 (2 1 .82) 1⁄8 (3. 1 8) 3⁄1 6 (4.76) 3⁄1 6 (4.76)
1 4 1 4.035 (356.48) ±0.01 5 (0.38) 0. 1 50 (3.81 ) 1 3.985 (355.22) ±0.01 5 (0.38) 0. 1 50 (3.81 ) 7.000 (1 77.80) 1 2.305 (31 2.55) 0.750 (1 9.05) 0.938 (23.83) 1⁄8 (3. 1 7) 3⁄1 6 (4.76) 3⁄1 6 (4.76)
1 6 1 6.045 (407.54) ±0.020 (0.5 1 ) 0. 1 60 (4.06) 1 5.980 (405.89) ±0.020 (0.5 1 ) 0. 1 60 (4.06) 8.000 (203.20) 1 4.093 (357.96) 0.843 (2 1 .41 ) 1 .054 (26.77) 1⁄8 (3. 1 7) 3⁄1 6 (4.76) 3⁄1 6 (4.76)
A The sketches and desi g ns of fitti ngs are i l l ustrative on ly (taken from Sym bols D2749) .
C See 6 . 1 . 4 .
B Socket depth , measu red from socket entrance face to socket bottom face .

D2467 - 15

TABLE 2 Dimensions of 90° Ells, Tees, Crosses, 45° Elbows and Couplings (Straight Sizes), in. (mm)
A

ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
Nominal Pipe Size Center to Thread End, 90° Elbows, Tees, Crosses, B H, min Length of Thread, T, min Center to Thread End, 45° Elbow, B K, min Inside Diameter of Fitting, D, min Nominal Wall Thickness, F, min Outside Diameter of Hub, M, min Thread End to Thread End of Coupling, L, min
1/8 0.688 (17.48) 0.38 (9.65) 0.625 (15.88) 0.215 (5.46) 0.118 0.645 (16.40) 0.813 (20.65)
1/4 0.812 (20.63) 0.50 (12.70) 0.688 (17.48) 0.302 (7.67) 0.149 0.840 (21.30) 1.063 (27.00)
3/8 0.938 (23.83) 0.50 (12.70) 0.750 (19.05) 0.423 (10.74) 0.160 1.000 (25.40) 1.063 (27.00)
1/2 1.125 (28.58) 0.64 (16.26) 0.750 (19.05) 0.550 (13.97) 0.185 1.280 (32.50) 1.344 (34.14)
3/4 1.250 (31.75) 0.65 (16.51) 1.000 (25.40) 0.750 (19.05) 0.195 1.500 (38.10) 1.500 (38.10)
1 1.500 (38.10) 0.81 (20.57) 1.125 (28.58) 0.960 (24.38) 0.225 1.810 (45.97) 1.688 (42.88)
11/4 1.750 (44.45) 0.85 (21.59) 1.313 (33.35) 1.280 (32.51) 0.261 2.200 (55.88) 1.750 (44.45)
11/2 1.938 (49.23) 0.85 (21.54) 1.438 (36.53) 1.500 (38.10) 0.270 2.500 (63.50) 2.000 (50.80)
2 2.250 (57.15) 0.90 (22.86) 1.625 (41.28) 1.940 (49.28) 0.297 3.000 (76.20) 2.063 (52.40)
21/2 2.688 (68.28) 1.21 (30.73) 1.938 (49.23) 2.320 (58.93) 0.345 3.580 (90.42) 2.625 (66.68)
3 3.063 (77.80) 1.30 (33.02) 2.125 (53.48) 2.900 (73.66) 0.405 4.300 (104.22) 2.750 (69.85)
4 3.625 (92.08) 1.38 (35.05) 2.625 (66.68) 3.830 (97.28) 0.450 5.430 (137.92) 3.000 (76.20)
6 5.125 (130.18) 1.50 (38.10) 3.250 (82.55) 5.761 (146.33) 0.540 7.625 (193.68) 3.250 (82.55)
A The sketches and designs of fittings shown are illustrative only.
B This dimension locates the end of the fitting.

If upon retest, failure occurs, the quantity of product represented by the test(s) does not meet the requirements of this specification.

10 Product Marking

10.1 Quality of Marking—The markings shall be applied to the fittings in such a manner that they remain legible under normal handling and installation practices.

10.2 Content of Marking—Fittings shall be marked with the following:

10.2.1 Material designation PVC I for PVC 12454, PVC 13 11443, and PVC II for PVC–14333,

10.2.2 The seal or mark of the laboratory making the evaluation for potable water contact,

10.2.3 Size, and

10.2.4 This designation, D2467, with which the fitting complies.

10.3 Where the size of the fitting does not allow complete marking, omit identification marking in the following sequence: size, material designation (D2467), manufacturer’s name, or trademark.

10.4 Marking or symbols shall be molded, hot-stamped, or applied to fittings by any other suitable method, such as printing.

10.5 Where recessed marking is used, care shall be taken to see that in no case does marking cause cracks or reduce the wall thickness below the minimum specified.

11 Quality Assurance

11.1 Quality Assurance—When the product is marked with this designation, D2467, the manufacturer affirms that the product was inspected, sampled, and tested in accordance with this specification and has been found to meet the requirements of this specification.

12 Keywords

12.1 blunt start thread; fittings; IPS; PVC; Schedule 80; sockets; thread

TABLE 3 Minimum Dimensions from Center to End of Sockets (Laying Length) for Couplings, Tees, 90° and 45° Elbows, PVC Socket-Type Pipe Fittings, Schedule 80, in. (mm)
A

ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
Nominal Pipe Size G, min J, min N, min
1⁄8 1⁄4 (6.35) 1⁄8 (3.18) 1⁄16 (1.59)
1⁄4 5⁄16 (7.94) 5⁄32 (3.97) 1⁄16 (1.59)
3⁄8 3⁄8 (9.53) 3⁄16 (4.76) 3⁄32 (2.38)
1⁄2 1⁄2 (12.70) 1⁄4 (6.35) 3⁄32 (2.38)
3⁄4 9⁄16 (14.29) 5⁄16 (7.94) 3⁄32 (2.38)
1 11⁄16 (17.46) 5⁄16 (7.94) 3⁄32 (2.38)
11⁄4 7⁄8 (22.22) 3⁄8 (9.53) 3⁄32 (2.38)
11⁄2 1 (25.40) 7⁄16 (11.11) 3⁄32 (2.38)
2 11⁄4 (31.75) 5⁄8 (15.88) 3⁄32 (2.38)
21⁄2 11⁄2 (38.10) 11⁄16 (17.46) 3⁄16 (4.76)
3 113⁄16 (46.04) 3⁄4 (19.05) 3⁄16 (4.76)
31⁄2 21⁄8 (53.98) 1 (25.40) 3⁄16 (4.76)
4 25⁄16 (58.74) 1 (25.40) 3⁄16 (4.76)
5 3 (76.20) 13⁄8 (34.93) 3⁄16 (4.76)
6 31⁄2 (88.90) 13⁄4 (44.45) 1⁄4 (6.35)
8 41⁄2 (114.30) 2 (50.80) 1⁄4 (6.35)
10 511⁄16 (144.46) 21⁄4 (57.15) 1⁄4 (6.35)
12 67⁄8 (174.63) 21⁄2 (63.50) 3⁄8 (9.53)
14 71⁄8 (180.97) 3(76.20) 3⁄8 (9.53)
16 81⁄2 (215.90) 33⁄8 (85.73) 3⁄8 (9.53)
A The sketches and designs of fittings are illustrative only (taken from Symbols D2749).

TABLE 4 Symbols for Dimensions of Reducer Bushings, PVC Socket-Type Pipe Fittings, Schedule 80,
A
in. (mm)

ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
TABLE 5 Dimensions of Plugs and Caps, in.
Nominal Size Outside Diameter XA Tolerance on Outside Diameter Outside Diameter XB Tolerance on Outside Diameter Maximum Out-of-Roundness (max., minus min.)
1⁄4 by 1⁄8 0.540 (13.72) +0.007 - 0.004 (0.18 - 0.10) 0.540 (13.72) ±0.004 (0.10) 0.016 (0.41)
3⁄8 by 1⁄4, 1⁄8 0.675 (17.41) +0.007 - 0.004 (0.18 - 0.10) 0.675 (17.41) ±0.004 (0.10) 0.016 (0.41)
1⁄2 by 3⁄8, 1⁄4 0.840 (21.34) +0.007 - 0.004 (0.18 - 0.10) 0.840 (21.34) ±0.004 (0.10) 0.016 (0.41)
3⁄4 by 1⁄2, 3⁄8, 1⁄4 1.050 (26.67) +0.007 - 0.004 (0.18 - 0.10) 1.050 (26.67) ±0.004 (0.10) 0.020 (0.51)
1 by 1⁄2, 3⁄4 1.315 (33.40) +0.008 - 0.005 (0.20 - 0.13) 1.315 (33.40) ±0.005 (0.13) 0.020 (0.51)
11⁄4 by 1⁄2, 3⁄4, 1 1.660 (42.16) +0.008 - 0.005 (0.20 - 0.13) 1.660 (42.16) ±0.005 (0.13) 0.024 (0.61)
11⁄2 by 1⁄2, 3⁄4, 1, 11⁄4 1.900 (48.26) +0.010 - 0.006 (0.25 - 0.15) 1.900 (48.26) ±0.006 (0.15) 0.024 (0.61)
2 by 1⁄2, 3⁄4, 1, 11⁄4, 11⁄2 2.375 (60.33) +0.010 - 0.006 (0.25 - 0.15) 2.375 (60.33) ±0.006 (0.15) 0.024 (0.61)
21⁄2 by 2 2.875 (73.03) +0.012 - 0.007 (0.30 - 0.18) 2.875 (73.03) ±0.007 (0.18) 0.030 (0.76)
3 by 21⁄2, 2 3.500 (88.90) +0.013 - 0.008 (0.33 - 0.20) 3.500 (88.90) ±0.008 (0.20) 0.030 (0.76)
31⁄2 by 21⁄2, 2 4.000 (101.60) +0.013 - 0.008 (0.33 - 0.20) 4.000 (101.60) ±0.008 (0.20) 0.030 (0.76)
4 by 31⁄2, 3, 21⁄2, 2 4.500 (114.30) +0.015 - 0.009 (0.38 - 0.23) 4.500 (114.30) ±0.009 (0.23) 0.030 (0.76)
5 by 4 5.563 (141.30) +0.017 - 0.010 (0.43 - 0.25) 5.563 (141.30) ±0.010 (0.25) 0.060 (1.52)
6 by 5 6.625 (168.28) +0.018 - 0.011 (0.46 - 0.28) 6.625 (168.28) ±0.011 (0.28) 0.070 (1.78)
8 by 6 8.625 (219.08) +0.025 - 0.015 (0.64 - 0.38) 8.625 (219.08) ±0.015 (0.38) 0.090 (2.29)
10 by 6 10.750 (273.05) +0.025 - 0.015 (0.64 - 0.38) 10.750 (273.05) ±0.015 (0.38) 0.100 (2.54)
10 by 8 10.750 (273.05) +0.025 - 0.015 (0.64 - 0.38) 10.750 (273.05) ±0.015 (0.38) 0.100 (2.54)
12 by 6 12.750 (323.85) +0.025 - 0.015 (0.64 - 0.38) 12.750 (323.85) ±0.015 (0.38) 0.120 (3.05)
12 by 8 12.750 (323.85) +0.025 - 0.015 (0.64 - 0.38) 12.750 (323.85) ±0.015 (0.38) 0.120 (3.05)
12 by 10 12.750 (323.85) +0.025 - 0.015 (0.64 - 0.38) 12.750 (323.85) ±0.015 (0.38) 0.120 (3.05)
A The sketches and designs of fittings are illustrative only (taken from Symbols D2749).
ASTM D2467-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule
Nominal Pipe Size Length of Male Thread, S, min Length of Female Thread, T, min Width of Flats, A Q, min Nominal Wall Thickness, F, min Height of Head, R, min Cap Height, W, min Outside Diameter of Hub, M, min
1/8 0.31 (7.87) 0.38 (9.65) 0.469 (11.19) 0.108 (2.74) 0.188 (4.76) 0.625 (15.88) 0.645 (16.38)
1/4 0.44 (11.18) 0.50 (12.70) 0.625 (15.88) 0.135 (3.43) 0.188 (4.76) 0.688 (17.48) 0.840 (21.34)
3/8 0.44 (11.18) 0.50 (12.70) 0.750 (14.05) 0.144 (3.66) 0.188 (4.76) 0.688 (17.48) 1.000 (25.40)
1/2 0.53 (13.45) 0.64 (16.26) 0.938 (23.83) 0.198 (5.03) 0.188 (4.76) 0.875 (22.23) 1.280 (32.51)
3/4 0.55 (13.97) 0.65 (16.51) 1.125 (28.58) 0.207 (5.26) 0.219 (5.56) 1.000 (25.40) 1.450 (36.80)
1 0.68 (17.27) 0.81 (20.57) 1.375 (34.93) 0.225 (5.72) 0.219 (5.56) 1.188 (30.18) 1.810 (45.97)
11/4 0.71 (18.03) 0.85 (21.59) 1.750 (44.45) 0.261 (6.63) 0.281 (7.14) 1.250 (31.75) 2.200 (55.88)
11/2 0.72 (18.29) 0.85 (21.59) 1.875 (47.63) 0.270 (6.86) 0.313 (7.95) 1.250 (31.75) 2.450 (62.23)
2 0.76 (19.30) 0.90 (22.86) 1.875 (47.63) 0.297 (7.54) 0.313 (7.45) 1.375 (34.93) 3.000 (76.20)
21/2 1.14 (28.96) 1.21 (30.73) 1.875 (47.63) 0.369 (9.37) 0.375 (9.53) 1.625 (41.28) 3.560 (90.42)
3 1.20 (30.48) 1.30 (33.02) 2.000 (50.80) 0.405 (10.29) 0.375 (9.53) 1.750 (44.45) 4.250 (107.90)
4 1.30 (33.02) 1.38 (35.05) 2.000 (50.80) 0.450 (11.43) 0.375 (9.53) 2.000 (50.80) 5.350 (134.62)
6 1.44 (36.58) 1.50 (38.10) 2.000 (50.80) 0.504 (12.80) 0.500 (12.70) 2.125 (53.98) 7.625 (193.00)
A At the manufacturer’s option the head of the plug may be hexagonal, octagonal, square, or round. The sketches and designs of fittings shown are illustrative only.
TABLE 6 Burst Pressure Requirements for Water at 73°F (23°C) for PVC Socket-Type Pipe Fittings, Schedule 80
Nominal Size, in. Minimum Burst Strength
Classes 12454114psi , 13354, and43MPa Class 14333 psi MPa
1⁄8 3920 27.03 3060 21.10
1⁄4 3620 24.96 2830 19.51
3⁄8 2940 20.27 2300 15.86
1⁄2 2720 18.75 2120 14.62
3⁄4 2200 15.17 1720 11.36
1 2020 13.93 1580 10.89
11⁄4 1660 11.44 1300 8.96
11⁄2 1510 10.41 1180 8.14
2 1290 8.89 1010 6.96
21⁄2 1360 9.38 1060 7.31
3 1200 8.27 940 6.48
31⁄2 1110 7.65 860 5.93
4 1040 7.17 810 5.58
5 930 6.41 720 4.96
6 890 6.14 700 4.83
8 790 5.45 620 4.27
10 600 4.14 . . . . . .
12 580 4.00 . . . . . .
14 570 3.93 . . . . . .
16 560 3.86 . . . . . .

SUPPLEMENTARY REQUIREMENTS

GOVERNMENT ⁄ MILITARY PROCUREMENT

These requirements apply only to Federal ⁄ Military procurement, not domestic sales or transfers.

S1. Responsibility for Inspection—Unless otherwise specified in the contract or purchase order, the producer is responsible for the performance of all inspection and test requirements specified herein. The producer may use his own or any other suitable facilities for the performance of the inspection and test requirements specified herein, unless the purchaser disapproves. The purchaser shall have the right to perform any of the inspections and tests set forth in this specification where such inspections are deemed necessary to ensure that material conforms to prescribed requirements. NOTE S1.1—In U.S. Federal contracts, the contractor is responsible for inspection.

S2. Packaging and Marking for U.S. Government Procurement:

S2.1 Packaging—Unless otherwise specified in the contract, the materials shall be packaged in accordance with the supplier’s standard practice in a manner ensuring arrival at destination in satisfactory condition and which will be acceptable to the carrier at lowest rates. Containers and packing shall comply with Uniform Freight Classification rules or National Motor Freight Classification rules.

S2.2 Marking—Marking for shipment shall be in accordance with Fed. Std. No. 123 for civil agencies and MIL-STD-129 for military agencies. NOTE S2.1— The inclusion of U.S. Government procurement requirements should not be construed as an indication that the U.S. Government uses or endorses the products described in this document.

POTABLE WATER REQUIREMENT

This requirement applies whenever a Regulatory Authority or user calls for product to be used to convey or to be in contact with potable water.

S3. Products intended for contact with potable water shall be evaluated, tested and certified for conformance with ANSI/ NSF Standard No. 61 or the health effects portion of NSF

Standard No. 14 by an acceptable certifying organization when required by the regulatory authority having jurisdiction.

Committee F17 has identified the location of selected changes to this standard since the last issue (D2467–13a) that may impact the use of this standard.

(1) Addition of 14 and 16 fitting data to Table 1, Table 3, and Table 6.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

资源下载此资源下载价格为5金币立即购买,VIP免费

1.本站大部份文档均属免费,部份收费文档,经过本站分类整理,花了精力和时间,收费文档是为了网站运营成本等费用开支;
2.购买会员:全部免费下载本站资源(或单次下载)即视为对网站的赞助、打赏,非商业交易行为(不认同此观点请勿支付)请慎重考虑;
3.所有收费文档都真实可靠,为了节约成本,文档在网站前台不做预览,如果付费后,与实际文档不符合,都可以加微信号:pdftj888申请退款;
4.付费下载过程中,如果遇到下载问题,都可以加微信号pdftj888解决;
5.手机支付,尽量选择支付宝支付;
6.如图集或者标准不清楚,在本站找不到您需要的规范和图集,希望增加资料等任何问题,可联系微信号:pdftj888解决;

文档天下
  • 本文由 发表于 2026年11月22日 16:49:01
  • 转载请务必保留本文链接:https://www.998pdf.com/84035.html
匿名

发表评论

匿名网友 填写信息

:?: :razz: :sad: :evil: :!: :smile: :oops: :grin: :eek: :shock: :???: :cool: :lol: :mad: :twisted: :roll: :wink: :idea: :arrow: :neutral: :cry: :mrgreen: